MSI 6741 DRIVER DOWNLOAD

Connect the fan power cable from the mounted fan to the 3-pin fan power connector on the board. If the mainboard has a System Hardware Monitor chipset on-board, you must use a specially designed fan with speed sensor to take advantage of the CPU fan control. Always consult the vendors for proper CPU cooling fan. Meanwhile, read the documentation for the expansion card to make any necessary hardware or software settings for the expansion card, such as jumpers, switches or BIOS configuration. J9 Optional You can connect a joystick or game pad to this connector. You must configure second hard drive to Slave mode by setting the jumper accordingly. You can attach a serial mouse or other serial devices directly to the connector.

Uploader: Zoloshicage
Date Added: 19 September 2008
File Size: 56.31 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 83516
Price: Free* [*Free Regsitration Required]

You can plug the USB device directly into the connector. Mount the fan on top of the heatsink. Locate the CPU and its retention mechanism on the motherboard. Overheating Overheating will seriously damage the CPU and system, always make sure the cooling fan can work properly to protect the CPU from overheating.

AGP is an interface specification designed for the throughput demands of 3D graphics. To connect to the ATX power supply, make sure the plug of the power supply is inserted in the proper orientation and the pins are aligned.

Line In is used for external CD player, Tape player, or other audio devices. If you do not find the heat sink and cooling fan, contact your dealer to purchase and install them before turning on the computer. If the CPU is correctly installed, the pins should be completely embedded into the socket and can not be seen.

  HL-DT-ST DVD-ROM GDR8163B ATA DEVICE DRIVER DOWNLOAD

Support For K8MM-ILSR | Motherboard – The world leader in motherboard design | MSI Global

When you are installing the CPU, make sure the CPU has a heat sink and a cooling fan attached on the top to prevent overheating. Make sure to raise the lever up to a 90degree angle. You can install either single- or double-sided modules in any order to meet your own needs. Also, it provides the instructions on connecting the peripheral devices, such as the mouse, keyboard, etc.

While doing the installation, be careful in holding the components and follow the installation procedures. It supports a three-pin head connector.

MSI MS Specifications |

J9 Optional You can connect a joystick or game pad to this connector. The CPU can only fit in the correct orientation.

Look for the gold arrow.

The plastic clip at each side of the DIMM slot will automatically close. Press the CPU down firmly into the socket and close the lever.

If you install two hard disks on cable, you must configure the second drive to Slave mode by setting its jumper. Please note that any violation of the correct installation procedures may cause permanent damages to your mainboard.

Memory modules can be installed in any combination as follows: The module will only fit in the right orientation.

Mic is a connector for microphones. Ms the heatsink onto the retention mechanism.

  INTEL DESKTOP BOARD D845HV LAN DRIVER DOWNLOAD

If the mainboard has a System Hardware Monitor chipset on-board, you must use a specially designed fan with speed sensor to take advantage of the CPU fan control. Avoid clearing the CMOS while the system is on; it will damage the mainboard. It’s a community-based project which helps to repair anything. As the CPU is likely to move while the lever is being closed, always close the lever with your fingers pressing tightly on top of the CPU to make sure the CPU is properly and completely embedded into the socket.

Connect the fan power cable from the nsi fan to the 3-pin fan power connector on the board. Refer to the hard disk documentation supplied by hard disk vendors for jumper setting instructions.

MSI MS-6741 Manuals

The third PCI slot supports 2 master devices. Always consult the vendors for proper CPU cooling fan. You can clear CMOS by shorting pin while the system is off. Meanwhile, read the documentation for the expansion card to make any necessary hardware or software settings for the expansion card, such as jumpers, switches or BIOS configuration. Before inserting the power supply connector, always make sure that all components are installed properly to ensure that no damage will be caused.