E510 PCI DRIVER DOWNLOAD

Cables routed over the cards can prevent the computer cover from closing properly or cause damage to the equipment. Ensure that the tab on the processor cover is positioned underneath the release lever at the front of the socket. Use care when handling the front-panel release tabs to avoid damaging them. You must position the processor correctly in the socket to avoid permanent damage to the processor and the computer when you turn on the computer. To connect a network cable, first plug the cable into the network port or device, and then plug the cable into the computer. When installing the processor, do not touch any of the pins inside the socket or allow any objects to fall onto the pins in the socket.

Uploader: Zolor
Date Added: 4 July 2018
File Size: 35.52 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 13141
Price: Free* [*Free Regsitration Required]

When you connect two IDE devices to a single IDE interface cable and configure them for the cable select setting, the device attached to the last connector on the interface cable is the master or boot device drive 0and the device attached to the middle connector on the interface cable is the slave device drive 1.

If you are not installing a processor upgrade kit from Dell, reuse the pic heat-sink assembly when you replace the processor. Only unbuffered, non-ECC memory is supported. Do not set the heat-sink assembly upright or touch the thermal interface, as this may result in damage to the r510 interface material. When removing or replacing the processor, do not touch any of the pins inside the processor pco or allow any objects to fall onto the pins in the socket.

If you remove your original memory modules from the computer during s510 memory upgrade, keep them separate from any new modules that you may have, even if you purchased the new modules from Dell. Your computer supports DDR2 memory. If the DDR2 memory modules are not installed in matched pairs, the computer will continue to operate, but with a slight reduction in performance.

  MSI MS-7336 LAN DRIVER DOWNLOAD

DDR2 memory modules should be installed in pairs of matched memory size, speed, and technology. If you are installing a new drive, you need to remove the drive-panel insert. Cables routed over the cards can prevent the computer cover from closing properly or cause damage to the equipment.

To guard against electrical shock, always unplug your computer from the electrical outlet before removing the cover.

While you work, periodically touch an unpainted metal surface to dissipate any static electricity that could harm internal components.

See the drive documentation in your upgrade kit for information on configuring devices for the cable select setting. Do not install ECC or buffered memory modules.

Dell Dimension – Wikipedia

When you install the heat-sink assembly, do not touch the thermal interface on its underside, as this may result in damage to the thermal interface material. When installing the processor, do not touch any of the pins inside the socket or allow any objects to fall onto the pins in the socket. Reversing the cable prevents the drive from operating and could damage the controller, the drive, or both.

The mounting-bracket screws need to be removed for the removal of the system board.

Use the pull-tab to remove the data cable from your hard drive or from the system board. You can do so by touching an unpainted metal surface on the computer.

For additional information on the type of memory supported by your computer, see your Owner’s Manual. Gently pull the securing tab, grasp the card by its top pic, and then ease it out of its connector. Ground yourself by touching an unpainted metal surface on the back of the computer.

  LVM2 WINDOWS DRIVER DOWNLOAD

Dell Dimension

Despite having a plastic shield, the heat-sink assembly may be very hot during normal operation. If you are installing or replacing a card, follow the procedures in the next section.

If the module is difficult to remove, gently ease the module back and forth to remove it from the connector. If the card is not removed correctly, the system board may be damaged. To avoid damage, ensure that the processor aligns ee510 with the socket, and do not use excessive force when you install the processor.

The pin-1 pcu of a connector on a board or a card is usually indicated by a silk-screened “1” printed directly on the board or card. Installing filler brackets over empty card-slot openings is necessary to maintain FCC certification of the computer. To loosen the two captive screws on each side of the heat-sink assembly, you need a long Phillips screwdriver.

If you are installing a processor upgrade e10 from Dell, discard the original heat-sink assembly. Grasp the card by its top corners, and ease it out of its connector. Otherwise, your computer may not start properly.

If necessary, disconnect any cables connected to the card.